|
|
Review: Toshiba HG6 256GB SSD |
Toshiba has been providing SSDs to OEMs for a long time, and
will no doubt continue to do so. Recently Toshiba acquired OCZ Technology,
which was a very wise move in my opinion. By acquiring OCZ, Toshiba gain a 'state
of the art' SSD controller in the shape of the Indilinx BareFoot 3, together
with OCZ's considerable knowledge in SSD controller and firmware knowhow.
About 16 months ago, I had the good fortune to be able to
publish a review on the Toshiba THNSNF512GCSS 512GB SSD, which I found to be a very capable performer.
Today I'm taking a look at a new Toshiba
range of SSDs aimed at the mainstream SSD market, in the shape of the Toshiba HG6
series of SSDs.
The Toshiba HG6 series of SSDs comes in various capacities
and form factors. The available capacities are, 60GB, 128GB, 256GB, and 512GB,
which are available in SATA 2.5 inch, mSATA, and M.2. form factors. The SSD I'm
looking at today is the 256GB SATA model.
So let's find out how this new SSD performs in our range of
tests.
Toshiba company information
Toshiba should need no introduction, but those of you who
would like to find out more about Toshiba Electronics Europe, can do so at
their website.
The Toshiba HG6 256GB SSD
Now it’s time to take a look at the drive itself and what it
came shipped with.
Packaging
The review sample I received was a pre-production unit, and
was simply shipped to me in a padded envelope.
Toshiba HG6 SSD range
The Toshiba HG6 range of SSDs is available in M.2., mSATA,
and 2.5 inch SATA form factors.
Drive bottom
Now let's head to the next page, where we look in more
detail at the Toshiba HG6 256GB SSD.....
A closer look at the Toshiba HG6 hardware.
PCB
PCB top side
The top side of the PCB contains no components at all on the
256GB model. I would expect to see the top side of the PCB populated with NAND
chip packages on the 512GB model.
PCB underside
The underside of the PCB hosts eight NAND chip packages, the
SSD controller, and we can also see various support components. Also note that
the Toshiba HG6 series does not use a DRAM cache solution.
The SSD controller
The SSD controller is labelled as Toshiba, is designated T635879BXBG,
and is Toshiba's own design.
The controller supports 'adaptive SLC emulation', and from
my tests this would appear to support SLC NAND emulation at up to 50% of the drive's
capacity. SLC emulation allows for much improved writing performance, providing
the SSD is less than half full of data.
In our review sample, the Toshiba T635879BXBG SSD controller
talks to the outside world via a SATA 6Gbps SATA revision 3.1 interface.
The NAND
The NAND is A19nm 'advanced' Toggle 2 mode MLC manufactured
by Toshiba. There are 8 packages onboard the Toshiba HG6, giving a total of
256GB, and the HG6 series of SSDs is the first SSD in the world to use this
advanced 19nm toggle 2 mode MLC NAND.
DATA encryption and protection
The Toshiba HG6 series is a self encryption based solution,
which is compliant with TCG-OPAL 2.0. The Toshiba HG6 series also features
Toshiba's proprietary Quadruple Swing-By Code error correction.
Drive maintenance features
For Windows 7 and Windows 8 users, and some distributions of
Linux, the Toshiba HG6 series SSD supports ATA TRIM to keep the NAND clean. The
Toshiba HG6 series also has advanced garbage collection to clean the NAND
during drive idle periods.
Specifications
Let’s head to the next page where we take a look at our
testing methods and the review PC....
Test machine
For this review I will be using a computer with the
following configuration:
Hardware:
- Motherboard: Asus Z87 SaberTooth (Intel Z87 chipset)
- Processor: Intel 4th generation Core i7 4770K
- CPU cooler: BeQuiet Dark Rock Pro 2
- RAM: 16GB Samsung Green DDR3 1600MHz (dual channel)
- GFX: Onboard Intel HD 4600
- Sound: Onboard Realtek ALC1050 HD audio controller
- Hard disk OS: OCZ Vector 256GB SSD.
- Case: Antec Performance One P280
- PSU: Antec True Power modular 550W
- Display: Dell UltraSharp U2412M 24” widescreen IPS LCD (HDCP
compliant) - Operating System: Windows 8.1 Professional 64bit
AHCI mode was also selected for all drives in the UEFI of our
test PC, and all tests were carried out in this mode. The SATA 6Gbps drivers
used on our review PC were the Intel Rapid Storage Technology (RST) Version
12.8.0.1016.
CPU power saving states were disabled for consistency, and
all the SSDs in this article were tested with all CPU power saving states
disabled.
Test applications
To test the performance of the Toshiba HG6 SSD, I will be
using the following test applications in this review.
- HD-Tune Pro
- ATTO
- Iometer
- AS SSD
Benchmark - CrystalDiskMark
- MyCE Reality Suite
- Anvil’s
Storage Utilities - PC
Mark 8
Test procedures
I will start off our testing procedures explanation by
stating that I did not run many synthetic benchmarks on the Toshiba HG6 SSD.
You may ask why I have run so few synthetic benchmarks?
SSD technology has moved so fast in the last couple of years,
that basic synthetic benchmarks alone are now of very limited use, as they don't
really tell us much about performance and how the drive will behave in the real
world. I have therefore decided to show some basic benchmarks of the Toshiba
HG6 SSD, and will complement this with advanced benchmarks using IOMeter and AS
SSD benchmark. I will also show how the Toshiba HG6 SSD performs in the real
world with our Myce Reality Suite test.
The reality of SSD performance
Whilst I can easily show you which SSD is technically the
faster, when you use one of these modern SSDs as an operating system drive it
becomes very difficult to tell them apart as far as performance is concerned.
A typical use of a small capacity SSD at the moment is to
have your operating system and applications installed onto the SSD. The
performance difference compared to a traditional HDD is enormous, however when
you start to compare SSD to SSD the difference becomes almost impossible to
detect.
Let’s look at why this is the case.
Drive A can boot to the desktop in 8.11 seconds, and drive B
can boot to the desktop in 8.12 seconds, the difference in time is
milliseconds, and can one really tell the difference?
The fact is, all modern SSDs are only ticking over when they
are only running the OS and launching applications, it’s only when you get to
some of the larger capacity SSDs, with enough free space to be able to hold the
actual data that you’re going to be working with, be that video, audio or
pictures, for example, that you actually get a tangible difference in
performance. This is where the SSDs with the better sequential performance start
to pull well ahead of the SSDs which have lower sequential read/write
performance.
Small file random IOPS vs sequential performance
IOPS
This is a fairly complex subject, but I will do my best to
explain things in a manner that is easy to understand.
The term IOPS is the amount of input or output transactions
that can take place in a one second interval, so for example, if an SSD is
quoted as being able to cope with 20,000 4K random write IOPS, then the SSD
should be able to cope with 20,000 input transactions in a period of one
second. If the same SSD is said to be able to produce 20,000 4K random read
IOPS, then the same SSD should be able to produce 20,000 4K random read output
transactions in a one second interval.
Ok, now we have some figures to work with, the next question
is how many IOPS are actually required?
This will depend on your usage pattern. If you are a typical
desktop user who browses the internet, does some word processing or perhaps
some audio or video editing, and perhaps plays a few games, then in actual
fact, you don’t need to have massive 4K random read/write performance. The
actual amount of 4K random performance that is required for a fast and smooth
running system for a desktop user with a usage pattern similar to the above
will be well under 1,000 4K IOPS.
On the other hand, if the SSD is being used for running a
large and complex database server, then 4K random performance is the absolute
measurement of how fast that server will run, as this type of application does
most of its input and output transactions in the 4K domain.
So why would I need an SSD with 80,000 4K IOPS for a
desktop?
In fact you don’t need this type of performance for a
desktop, but an SSD which is capable of coping with 80,000 4K IOPS will be
faster than an SSD which can only cope with 20,000 4K IOPS.
OK, I just said if under 1,000 4K IOPS are actually required
for typical desktop usage, why is an SSD with 80,000 4K IOPS faster than an SSD
with only 20,000 4K IOPS, confused?
You may ask, if I only require 1,000 4K IOPS surely the rest
is wasted?
While you may never need 80,000 4K IOPS, IOPS is all about
latency. The reason that an SSD can cope with as much as 80,000 4K IOPS is
because latency in this domain is very low. With 4K files, even if you require
to process 500 of them at the same time, you are not talking about a huge
amount of data, it has far more to do with how long it takes the SSD to process
a single file, and the amount of time required to process a single 4K is all
about how long it takes for the SSD to access or store that data before it can
move on to the next transaction.
In other words an SSD with 80,000 4K IOPS performance will
handle those 500 files faster than the SSD with 20,000 IOPS.
So how will a desktop user even notice this faster speed if
so little 4K random IOPS and data are actually used?
Multitasking is a good example. The more tasks you run at
the same time, you more you will notice the speed difference.
Sequential performance
I have always maintained that sequential performance was
every bit as important as small random file performance for a desktop SSD. To
me this was always so obvious for a desktop user. For example, let’s say you
want to launch an application or game. Both have some fairly large files to
load, and also a great many small files, but the point is, even the smaller
files are sequential in nature. Now let’s say you’re into audio or video
editing. Video files tend to be huge, and the files are written or read
sequentially. Isn’t this how many users are using their PCs these days?
Summary
So how does this shape up in the real world? Which is
better, massive 4K IOPS or massive sequential performance?
In an ideal world you want both, as an SSD with massive
random 4K IOPS and sequential performance will always be faster than an SSD
that has high sequential performance and moderate 4K random IOPS performance,
and the same applies to an SSD that has massive 4K random performance and
moderate sequential performance. The SSD which has high performance in both
patterns will always be the faster SSD.
However, you can still have an SSD that is very fast for
desktop use that has moderate random 4K performance and massive sequential
performance, the same can be said about a drive having massive random 4K
performance and moderate sequential performance, as it is about getting the
balance right if you have to compromise on one or the other.
Test drives
- Intel 520 series 240GB
- OCZ Vertex 4 512GB SSD
- Corsair Neutron GTX 240GB SSD
- OCZ Vector 256GB SSD
- Toshiba THNSNF512GCSS
512GB SSD - Samsung 840 Pro 512GB SSD
- Plextor M5 Pro 512GB SSD
- Samsung 840 250GB SSD
- Kingston V300 240GB SSD
- OCZ Vertex 3.20 240GB SSD
- OCZ Vertex 450 256GB SSD
- Seagate 600 series 480GB SSD
- Samsung 840 EVO 250GB SSD
- Samsung 840 EVO 750GB SSD
- OCZ Vector 150 240GB SSD
- Samsung 840 EVO mSATA 1TB SSD
- Samsung 840 EVO mSATA 250GB
SSD - OCZ Vertex 460 240GB SSD
- Crucial M550 512GB SSD
- Toshiba HG6 256GB SSD
Drive preparation for running the tests
All the SSDs used in this article were in a clean and fresh
state when the testing period started. From then on, each drive had to rely on
its own NAND cleaning effectiveness for the remainder of the tests.
For the sake of clarity, I now only include SATA 6Gbps SSDs
in these tests, and all were connected to the native Intel SATA 6Gbps (port 0)
of my motherboard for these tests.
- All SSDs used in this article had their partitions aligned
to the Windows 8.1 x64 defaults.
Where I use graphs in this article to display results, I
will use the following colours to make it easier, for our readers to see which drive
we are reviewing.
Toshiba HG6 256GB SSD
Comparison SSD
Now let's head to the next page, where I look at some
basic benchmarks...
Synthetic Benchmarks
HD Tune Pro
In this benchmark I am checking sequential reading speed.
With an average sequential reading speed of 518.4 MB/s the Toshiba
HG6 SSD shows an excellent turn of speed. Also worth noting are the incredibly
fast access times.
Let's see how this compares to other recently tested SSDs in
the table below.
The Toshiba HG6 256GB SSD has done extremely well in the HD
Tune Pro 5 sequential reading test, and whilst there isn't a large margin
between the top SSDs, the Toshiba HG6 256GB is the fifteenth fastest in this
test.
ATTO disk benchmark
ATTO has become a standard tool for measuring the data
throughput of HDDs and SSDs. It measures the reading and writing performance,
using different file sizes and block sizes.
The reading speed results on the Toshiba HG6 256GB SSD are
extremely impressive, topping out at over 554 MB/s, and writing speed is
equally impressive topping out at nearly 521 MB/s.
Let's find out how this compares with other recently tested
SSDs.
ATTO Reading performance
ATTO - Reading performance at various block sizes
The Toshiba HG6 SSD is one of the fastest SSDs when reading
data.
ATTO Writing performance
ATTO - Writing performance at various block sizes
The Toshiba HG6 SSD shows excellent writing performance.
CrystalDiskMark 3.0
Crystal Disk Mark is quite a handy benchmarking application,
as it focuses on the file sizes that can cause a problem on a system drive.
As we can see from the above screenshot, sequential reading and
writing speeds are both very impressive, and random writing performance at low
and high queue depths is very good.
AS SSD Benchmark
AS SSD benchmark is a benchmarking tool specifically
designed to test SSDs. The application tests sequential reading and writing
performance, 4K random reading and writing performance.
AS SSD benchmark also tests 4K threaded performance. This is
very exciting, as this test is the first available test that I am aware of,
that simulates how a PC operating system actually works. A modern PC and OS,
such as Windows 7/8 does not just run a single thread at a time, it runs many
threads. The AS SSD benchmark "4K 64Thrd" tests run 64 threads
simultaneously throughout the test. If this result is good, then you can be
pretty sure the drive will perform extremely well as a system drive.
After the tests complete, AS SSD benchmark derives a total
score for the drive being tested. This is based on all aspects of the test
results, and gives an indication of how the drive is performing overall.
Now let’s look at the result from the Toshiba HG6 SSD in the
form of a screenshot. All our other comparison drives’ results are presented in
the form of a graph.
Toshiba HG6 256GB SSD
As we can see from the AS SSD test run, the Toshiba HG6 SSD
has excellent reading and writing performance, finishing this test in
fourteenth place overall.
Summary:
The Toshiba HG6 256GB SSD has performed extremely well in
the basic synthetic benchmarks. Random reading and writing performance is very
impressive. Sequential reading and writing performance is outstanding.
Let's head to the next page for our IOMeter test
results.....
I/O Performance
There is little point of having an SSD drive that has
blazing sustained reading and writing speeds, if the drive can't handle reading
and writing of small random files. If you intend to use your new SSD drive to
store and run your operating system, then the drive must be able to cope with
the many small random files that Windows will write to the drive continually.
So I feel it is very important to test how many of these random files that a
drive can handle in one second. I believe that anything over 1,000 I/O’s per
second would be enough for most users running a consumer grade mainstream PC,
and should provide a smooth running system. But obviously, the more I/O's that
a drive can handle, the faster the drive will feel and leave more headroom for
those huge multitasking sessions that users sometimes engage in.
IOMeter is probably the most versatile of all the synthetic
benchmarks. Its ability to be configured to generate a multitude of different
I/O traffic is unmatched. Another great feature of IOMeter, is the capability
to test any storage metric that you can think of, providing you know how to
configure the assignments. The reviewer also has complete control over things
like queue depth, block size, whether the traffic is random, sequential, or
even a mixture of both.
Partition alignment and sector boundaries
Windows 8.1, Windows 7, and Windows Vista will automatically
align a partition to 4k boundaries during partition creation, Windows XP won’t.
It is imperative that an SSD’s partition is aligned. Windows XP is also
restricted to sector boundaries, while Windows 7 and 8 will use 4k boundaries
if they can. The Toshiba HG6 SSD is 4k boundary aware, and will use these
boundaries if possible. Of course it will also remap LBAs for compatibility
with the sector boundaries so that the drive can be used with Windows XP.
IOMeter allows us to set the sector boundaries for
conducting the tests, and I have therefore set the sector boundaries at 4K,
which means the IOMeter tests are valid for Windows 7, Windows 8, and Windows
Vista users. XP users will not be able to obtain such results.
I will provide a screenshot of the tests on the review drive
for those of you who like to see the actual test result. All the comparison
drive results are represented in the form of graphs.
If any of you would like to see a screenshot from any
IOMeter test on a particular drive, please feel free to request one, and I’ll
post the screenshot in the forum thread.
All the IOMeter tests create a 10GB data set on the target
drive, and each test is run for a duration of 3 minutes.
IOMeter 4K random write test with repeating data.
The first test involves creating continual 4KB random files
on the target drive with IOMeter. I use a 4KB file size, as it is believed that
Windows will create and modify many of this size of file constantly in the background
during a typical Windows session. It is said that most 4K random writes take
place at a queue depth of only one, and I have been requested to include this
test in my reviews.
Queue depth 1
Toshiba HG6 256GB SSD – 4K random write (QD 1)
At 137.14 MB/s the Toshiba HG6 256GB SSD is excellent, and
finishes this test in eighth place.
Our next test involves creating continual 4KB random files
on the target drive with IOMeter. I use a 4KB file size, as it is believed that
Windows will create and modify many of this size of file constantly in the
background during a typical Windows session. I will use queue depths of 4 and
32 for these tests.
Queue depth 4
Toshiba HG6 256GB SSD (QD 4)
At a queue depth of 4, the Toshiba HG6 SSD delivers good
performance, and finishes this test in nineteenth place.
Queue depth 32
Toshiba HG6 256GB SSD (QD 32)
At 250.42 MB/s, the Toshiba HG6 256GB SSD lags behind quite
a lot of the SSDs in this test, and finishes this test in twenty first place.
IOMeter 4K random write test with fully random data.
This test is exactly the same as the test above except that
the test data is fully random and is therefore much more difficult to compress.
This test was requested as SandForce based SSDs gain a lot of performance by
being able to compress data on the fly. While the above test shows the
SandForce based SSDs in a best case scenario, the following test will show the
SandForce based SSDs in a much more realistic scenario.
Queue depth 4 with fully random data
Toshiba HG6 250GB SSD – 4K random write (QD 4 with fully random data)
The Toshiba HG6 SSD pays no penalty when writing data which
is incompressible, and with 249.44 MB/s it finishes the test in fifteenth
place.
4K random write queue depth profile
For this test I used various queue depths from 1 – 32 to
give you an idea how this SSD performs at different queue depths. For a normal
desktop user, with lightweight multitasking, the queue depth will rarely rise
above 2. For heavy multitasking, the queue depth is unlikely to rise above a
value of 8.
The results are shown below.
As we can see, the Toshiba HG6 SSD has very good performance
at low queue depths, but after it reaches a queue depth of 3, performance
doesn't increase with higher queue depths.
Below I present a table of the results in more detail.
IOMeter 4K random read test.
If there are many 4k files created, then that must also mean
that many 4k files need to be read. This test measures 4k reading performance.
It is said that most 4K random reads take place at a queue
depth of only one, and readers have requested that I include this test in my
reviews.
Queue depth 1
Toshiba HG6 256GB SSD - 4K random read (QD 1)
In this test the Toshiba HG6 SSD has good performance, and
finishes in eighteenth place.
Queue depth 4
Toshiba HG6 256GB SSD - 4K random read (QD 4)
Once again the Toshiba HG6 is good, and finishes this test
in thirteenth place.
Queue depth 32
Toshiba HG6 256GB SSD - 4K random read (QD 32)
At a queue depth of 32, the Toshiba HG6 SSD is showing excellent
performance, but still only manages to finish this test in twelfth place.
4K random read queue depth profile.
This test shows how the review drive scales with increasing
queue depths.
Below I present a table of the results in greater detail.
If we look at the Toshiba HG6 SSD 4K random read performance
in detail, at low queue depths, the performance is very good, and the Toshiba
HG6 scales almost perfectly all the way up to a queue depth of 32.
IOMeter 512KB sequential write test with repeating data.
Sequential writing performance is also very important; in
this test sequential writing performance is measured.
Toshiba HG6 256GB SSD - 512K Sequential write with repeating data
The Toshiba HG6 SSD shows an excellent turn of speed, finishing
this test in twelfth place, and is only marginally slower than the fastest SSD
in this test.
512K sequential write - Queue depth profile
While most sequential writes will rarely rise above a queue
depth of two, it has been noted from SATA analyzer traces that with more
demanding tasks, queue depths can rise very close to a queue depth of four.
This is why I now include queue depth profiles for sequential read and write.
Please note that in the following graph, I do not have the
lowest possible score set at zero. This is purely to allow the graphs to be
easier to read, but starting with a lowest possible score other than zero,
gives the impression that there are large differences between competing SSDs with
regard to performance, so please keep this in mind.
512K sequential write - Queue depth profile
Below I present a table of the results in more detail.
The Toshiba HG6 SSD series reaches peak performance at queue
depths of three and four, where it manages an impressive 520.93 MB/s.
IOMeter 512KB sequential write test with fully random data.
This test is almost exactly the same as the test above
except that the test data is fully random in nature. This test was requested as
SandForce based SSDs gain a lot of performance by being able to compress data
on the fly. While the above test shows the SandForce based SSDs in a best case
scenario, the following test will show the SandForce based SSDs in a more
realistic light. In the real world, the data is neither 100% incompressible nor
100% compressible, it is somewhere in between. So please keep this in mind.
Toshiba HG6 256GB SSD – 512K sequential write with fully random data
With data that is not so easy to compress, the SandForce SF-2281
based SSDs take a big performance hit, whilst the Toshiba HG6 SSD returns an
impressive 520.61 MB/s, and finishes this test in ninth place.
IOMeter 512KB sequential read test QD1.
This test measures 512k sequential reading performance at
very low queue depths.
Toshiba HG6 256GB SSD – 512K sequential reading test (QD 1)
The Toshiba HG6 256GB SSD has outstanding sequential reading
performance at very low queue depths, finishing in third place.
IOMeter 512KB sequential read test (dual threaded).
This test measures 512k sequential reading performance QD2.
Toshiba HG6 256GB SSD – 512K sequential reading test (QD 2)
At a more realistic queue depth the Toshiba HG6 256GB is still
showing outstanding sequential reading performance, and finishes this test in
ninth place.
512K sequential read - Queue depth profile
While most sequential reads will rarely rise above a queue
depth of two, it has been noted from SATA analyzer traces that with more
demanding tasks, queue depths can rise very close to a queue depth of four.
This is why I now include queue depth profiles for sequential read and write.
Please note that in the following graph, I do not have the
lowest possible score set at zero. This is purely to allow the graphs to be
easier to read, but starting with a lowest possible score other than zero,
gives the impression that there are large differences between competing SSDs with
regard to performance, so please keep this in mind.
512K sequential read - Queue depth profile
Below I present a table of the results in greater detail.
The Toshiba HG6 SSD reaches maximum sequential reading performance
at a queue depth of four, where it achieves an outstanding 552.58 MB/s.
IOMeter Workstation simulation (outstanding I/Os = 64).
When running applications you will find that there is a
mixture of small random files and larger sequential files, being created and
read. Not only that, it isn’t just one file at a time. In this test I measure a
simulated workstation pattern, with a queue depth of 64 (threaded).
Toshiba HG6 256GB SSD – Workstation simulation
The 'workstation' simulation sorts the men out from the
boys, with its mixed reads and writes. This test shows how an SSD could behave
in a heavy workload, graphics or video workstation. The Toshiba HG6 SSD has
exceptional mixed read/write performance, and allows the HG6 to finish in third
place with a mighty impressive 444.35 MB/s.
Summary
All in all, the Toshiba HG6 256GB SSD has performed well in
our IOMeter tests. It has excellent reading performance, and writing
performance is very good across the board. The Toshiba HG6 has impressive mixed
read/write performance, and this is where the Toshiba HG6 really shines.
Now let’s head to the next page where we will look at how
the Toshiba HG6 SSD performs using a new benchmarking application....
Anvil’s Storage Utilities
As well as performing SSD endurance tests. Anvil’s Storage
Utilities has a very nice SSD benchmarking application. The SSD benchmark tests
many different aspects of SSD performance, including 4K random at different
queue depths, and also sequential performance, but more importantly than this,
all using real test data.
Another very nice feature of Anvil’s SSD benchmark is the
fact that you can change the compression levels of the test data. The
compression levels of the datasets used for the tests can be varied from 0%
compression right up to 100% compressed data, and there are even a few data
profiles already included, such as database (8%) compression, and also an
application profile (46%) compression, which is designed to simulate real
application data being read and written to the SSD.
I will include a screenshot of the review drive, and all
comparison results will be presented in the form of graphs. If you would like
to see screenshots of the test results obtained on the other SSDs in this
article, you can do so by following the link here.
I will also be testing three different compression profiles,
which are as follows.
- 0 fill (100% compressible data)
- Application simulation profile (46% compressed)
- 100% (incompressible data)
So let’s begin the tests.
0 fill
Toshiba HG6 256GB SSD (0 fill)
In the 0 fill test, the Toshiba HG6 SSD has performed well
and finishes this test in fifteenth place.
Application profile
Toshiba HG6 256GB SSD (application profile)
The application test pattern is much more realistic in terms
of the type of data that real users will employ, and this time the Toshiba HG6
SSD finishes in fourteenth place.
100% incompressible
Toshiba HG6 256GB SSD (100% incompressible)
With test data that can't be compressed at all, the Toshiba
HG6 SSD is still performing well, and on this occasion finishes the test in
fifteenth place.
Summary
One should keep in mind that although Anvil’s Storage
Utilities SSD benchmark is a very good benchmark, and tests many aspects of SSD
performance, ultimately it is demonstrating which SSD is technically the
fastest when reading data, and this may not be showing (for example) which
drive will be fastest in the real world with a home user's work pattern.
The Toshiba HG6 256GB SSD has however performed very well in
Anvil's SSD benchmark tests.
Now let's head to the next page for some real world tests....
It has become clear that simply conducting endless
benchmarks on SSD drives is pointless. Real users may run a few benchmarks when
they first fit their SSD drive, but most users just want a drive that performs
well in the real world. They want their drive to work "out of the
box" and run fast and smoothly.
Most of the latest SSD drives can deliver very fast
sustained reading and writing speeds, but these alone tell you very little
about how the drive will perform in the real world.
If you intend to use your SSD as your primary system drive,
with an operating system and applications installed and running from the drive,
real world performance becomes much more important than just fast sequential
read and write speeds.
Real world copy tests
I will now conduct a few real world copy tests. These tests
simulate what real people do with their drives. I will be conducting writing
tests, using a large single file, and I will then round off the tests by
copying a folder of MP3 audio files, and also a folder of JPG pictures.
In past reviews I simply used Windows copy and paste to copy
the files from one drive to the target drive, and then I measured the time
taken to complete the test with a stop watch. This method was flawed in a
couple of ways. Windows employs a cache, so even when the files had been
copied, some of the data was still in the Windows cache and hadn't yet been
written to the SSD. The other flaw was that a stop watch is not a very accurate
way of measuring the time taken to complete the test.
I had also noticed that copying the small file set had
become pointless, as most modern SSDs have a rather large cache, in fact large
enough to be able to take the complete file set in this cache without having to
commit that data to NAND before the test had completed. I could have increased
the amount of data in the test, but I felt this was moving away from the real
world. For example, who would copy 2GB of data containing only very small
files?
I concluded it was perhaps better just to drop this test
completely, and just focus on the large 8GB ISO file, the folder of MP3 audio
files, and the folder of JPG picture files. I also have taken the opportunity
to increase the amount of data to be copied in the MP3 and JPG tests, to make
sure the SSD's memory cache doesn't obtain an unfair advantage.
The other change is that I now use an application to copy
the data, which also times how long it takes to complete the test. This
application also supports "cache write-through". What this basically
means is, there is now no caching of the files, and instead the data being
copied must be committed to the target SSD as it's being copied.
Obviously making such changes to the methods of testing is
not taken lightly. To make changes means a lot of extra work, as all the
comparison drives have to be re-tested with the new method. However, here at
Myce.wiki, we believe we should always try to improve our reviews, and if that
means updating the testing methods and some initial extra work, then that benefits
the Myce community as a whole.
For the reading drive, I have made the switch to a RAMDisk.
With SATA Express SSDs just around the corner, the OCZ REVODrive X2 would no
longer be fast enough to supply data to a SATA Express SSD. Because RAM has
lower latency and higher transfer speeds when compared to an SSD, this has
meant having to rerun the tests on a selection of other SSDs to make sure the
results are up to date. Please note, that some SSDs which were on loan during
the review period, has meant that these SSDs still use the old results, simply
because I can't retest them.
For the tests themselves, I will show a screenshot of the
copy test for the SSD that I'm reviewing. All other results will be presented
in the form of a graph, so you can easily compare the results.
Single large file writing test (8144.6MB)
For this test I used a single DVD9 ISO file which had been
copied to the RAMDisk. The file was then copied to the Toshiba HG6 SSD and our
comparison drives.
Toshiba HG6 256GB SSD
The Toshiba HG6 SSD has excellent sequential writing
performance, and finishes this test in seventh spot.
Write a folder of JPG picture files.
For this test I copied a folder of JPG picture files from
the RAMDisk to the Toshiba HG6 SSD series 256GB SSD, and our other comparison
drives. The folder contained 7861 JPG pictures, with a total capacity of
8410.3MB.
Toshiba HG6 256GB SSD
Once again the Toshiba HG6 is performing extremely well, and
finishes in sixth place in this test.
Write a folder of MP3 audio files.
For this test I copied a folder of MP3 audio files from our RAMDisk
to the Toshiba HG6 SSD series SSD and our other comparison drives. The folder
contained 1691 MP3 audio files, with a total capacity of 9176.5MB.
Toshiba HG6 256GB SSD
Yet again the Toshiba HG6 256GB SSD is performing well, and
finishes this test in seventh spot.
Single drive copy tests
These tests are to simulate a single drive in a PC or
laptop. In other words, I will copy a series of files from one folder on the
tested drive to another folder on the same drive. This means the drive is simultaneously
reading and writing during the tests. I also want to make this a realistic test,
so I have used a folder of MP3 music files, and then repeated the test with a
folder of JPG picture files.
Single drive copy tests – 1,691 MP3 song files (9176.5MB total)
Toshiba HG6 256GB SSD
With this test the SSD has to read and write data, and we
already know that the Toshiba HG6 has excellent mixed reading and writing
performance, so it's no surprise to see the Toshiba HG6 finish this test near
the top of the table, in this case in fourth place, and only marginally slower
than the very fastest SSDs.
Single drive copy tests – 7,861 JPEG picture files (8410.3MB total)
Toshiba HG6 256GB SSD
The Toshiba HG6 256GB SSD finishes in third place in this
test.
Summary
The Toshiba HG6 256GB has performed extremely well in the
copy tests. With its high performance sequential writing speeds translating
into some very fast write times. The Toshiba HG6 also has very impressive mixed
read/write performance, and this has ensured that it has finished near the top
of the tables when the SSD is faced with having to simultaneously read and
write data.
Installing applications
Installing applications is possibly something you don't do
that often. But should you replace your system disk, then you will most likely
have to re-install your applications. Most of the SSD drives I have tested up
until now are quite slow at installing applications, most likely because their
I/O performance was quite limited.
For these tests, we picked some popular applications and
copied the entire contents of the CD or DVD media to a RAMDisk. We did this to
make sure that the reading speed of our CD/DVD reader would not hamper the
performance of the target drive.
We then installed these applications onto our comparison drives,
which were all running mirror image installations of our Windows 8 Professional
64-bit installation, and timed the amount of time taken to install the
application with a stopwatch on each of the drives.
MS Office 2007 Professional (full install)
MS Office is one of those applications that make you cringe
at the thought of re-installing it.
Let's find out how our drives coped with the MS Office 2007
full install.
The Toshiba HG6 SSD showed an excellent turn of speed when
installing this large office suite, and finished the test in joint fifth place,
along with two other drives.
Adobe Fireworks CS3
Adobe Fireworks CS3 is another popular package. Let's find
out how our drives coped with installing this application.
There isn’t a huge margin in the amount of time taken to
install this application on our modern SSDs. However, the Toshiba HG6 256GB SSD
finishes this test tied in sixth place with three other SSDs.
Summary
Our real world tests, though not scientific in nature, I
feel are more realistic than simply running benchmarks. What is clear from these
tests is that the Toshiba HG6 256GB SSD has excellent performance in the real
world.
Let’s check out application and game loading performance
on the next page of this article.....
These tests are very simple tests, but very important to
some users of SSD drives.
We simply started an application or game, and measured the
time taken for the application or game to fully load and start.
Application loading times
Adobe Fireworks CS3
There is so little difference in tangible performance between
the modern SSDs. However, the Toshiba HG6 256GB SSD loads this large application
in 3.38 seconds, and finishes the test in second place.
Corel PaintShop Pro 12
Again, I doubt anyone could tell difference from the fastest
to the slowest modern SATA 6Gbps SSD, as they are all very close.
Games loading times
FAR CRY 2
Once again the results are all very close, and I highly
doubt anyone could tell the difference between the fastest and slowest SSD in
this test.
F.E.A.R. 2
The Toshiba HG6 256GB SSD has performed very well, and is
amongst the fastest drives in this test.
Summary
By now it's is becoming very clear that the Toshiba HG6 256GB
SSD delivers excellent performance, and its excellent reading capabilities have
ensured that it's one of the fastest SSDs in these tests.
Now let's head to the next page where we will see how the
Toshiba HG6 SSD performs in PC Mark 8.....
PC Mark 8 - Storage Suite
Here at Myce.wiki, we only recently introduced PCMark Vantage
into our SSD testing. PCMark Vantage is a good test, but is now somewhat
outdated in the applications that it tests, even to the extent of including a
test trace on how Windows Vista booted. We could have course have opted for the
newer PCMark 7, but I personally had issues with the way it ran the HDD tests.
We have built quite a close relationship with FutureMark
software, the authors of the PCMark PC benchmarking software that we use in our
tests. I decided I would use PCMark Vantage as stopgap measure until the more
up-to-date PCMark 8 benchmarking suite became available. I'm pleased to say
that PCMark 8 is now available, and it gives me great pleasure to introduce you
all to the results obtained by this new 'real world' benchmarking suite.
I will describe the basic way that each test is carried out,
above the graph for each test.
PC Mark 8 storage suite results
Toshiba HG6 256GB
Now let’s look at the individual PC Mark 8 HDD suite scores,
in the form of tables and graphs.
PC Mark 8 storage suite: World of Warcraft
The first thing that is very noticeable is that all the
tested SSDs are remarkably close, performance wise, when loading this game.
PC Mark 8 storage suite: Battlefield 3
Once again, the results are very close between all the
competing SSDs.
PC Mark 8 storage suite: Adobe Photoshop light
Yet again the results are all very close together, with the
higher writing performance SSDs out in front.
PC Mark 8 storage suite: Adobe Photoshop heavy
Again, there isn't a large difference between any of the
competing SSDs, and the SSDs with the higher sustainable writing performance
are generally out in front.
PC Mark 8 storage suite: Adobe InDesign
Once again, the SSDs with the higher writing performance
head the table.
PC Mark 8 storage suite: Adobe After Effects
There is virtually no difference between the tested SSDs.
PC Mark 8 storage suite: Adobe Illustrator
Once again, there is hardly any difference between the
tested SSDs.
PC Mark 8 storage suite: Microsoft Word
With only 0.2 seconds between the fastest and the slowest
SSD in this test, I would doubt anyone could tell the difference.
PC Mark 8 storage suite: Microsoft Excel
There is only 0.2 seconds between the slowest and the
fastest SSD in this test.
PC Mark 8 storage suite: Microsoft PowerPoint
Once again, the results obtained from our test SSDs are
almost identical.
PC Mark 8 storage suite: Storage bandwidth
Storage bandwidth displays the amount of bandwidth available
from the storage device, when it is faced with requests for simultaneous reads
and writes.
According to PC Mark 8, the Toshiba HG6 has 317.97 MB/s of bandwidth,
which is the highest of any of our tested SSDs.
PC Mark 8 storage suite: Overall Score
PC Mark 8 sums all the individual times taken to run each
storage benchmark, then comes up with an overall score for each of the tested
SSDs.
As we can see from the above graph, there isn't a large
difference between any of the tested SSDs, but the Toshiba HG6 SSD takes first
spot along with the Samsung 840 Pro in these tests.
Summary
You may well ask, if the scores are so close between the
tested SSDs, then what is the point of running PC Mark 8 storage benchmark?
Basically, most of these individual tests are very low
demand as far as storage is concerned. More or less all the traces are
lightweight. But hang on a minute, this is how real applications work, and I
and many other reviewers have been saying for years that when we have
lightweight storage traces, it becomes almost impossible to tell SSDs apart
from a performance perspective. We now have a tool that can demonstrate this to
very good effect.
It's not until we start to push SSDs very hard that the
performance differences between SSDs start to become clearer, and for that we
need much heavier workloads, such as the tests run in the Myce Reality Suite.
PC Mark 8 is still very useful, as I'm quite sure that most of you will use at
least a couple of the applications used in these tests, and now you will be
able to compare one SSD to another.
Now let’s round off the performance tests with the Myce
Reality Suite on the next page.....
Myce Reality Suite revision 3.
So what is the Myce Reality storage test?
The Myce Reality Suite of tests is made from real everyday
applications and real data, there are no simulated tests, and everything is in
the real world. The only thing that's synthetic is that everything is automated
to make the tests fair, no matter which drive the tests are run on.
Recorded user sessions, by means of a script, are used to
launch the applications, load data, edit data, and then finally write that data
back to the target drive. The scripts do load the system much more than a human
could with these tests, as the scripts do not make mistakes, or pause to think
about what has to be done next.
Measurement system
The measuring system is part hardware and part software. The
hardware is a two part system comprising of a host PC and an external hardware
analyser which is proprietary, and runs a proprietary version of Linux with
special software.
The host PC is built around an Intel Core i7 2600 (Sandy
Bridge) CPU, and an Asrock Z68 Extreme 4 motherboard, with 8GB of 1600MHz DDR3
RAM. The interface between the host PC and the external measuring system uses a
proprietary PCIe2 x8 card, which is housed in the primary PCIe2 x16 slot on the
host PC. The analyser is calibrated before the start of the tests, and is
guaranteed to be accurate to within 0.03%.
Testing method.
Previously the test platform was Windows 7 Home Premium
64bit. The transition to Windows 8.1 Professional 64bit has now been made, and
at the same time a couple of new tests have been validated and introduced. This
has of course meant that I have had to retest a selected number of SSDs on the
new platform, and the results from SSDs that were old, or no longer available
in the test labs, have been discarded.
Building the tests and test image.
Once all the test data files and the scripts that run the
tests were complete, they were then copied to a single folder. I then fitted an
120GB SSD into the PC and did a clean install of Window 8.1 Professional x64.
The latest hardware drivers were installed and Windows update was run to
install any new updates that were available up to 24/11/2013. At this point the
applications that were to be used in the tests were installed and updated with
the latest patches.
The folder containing the application test data files and
scripts was then copied over to our fresh Windows 8.1 Professional 64bit SSD. A
drive snapshot was then taken of the complete SSD and the drive snapshot image
copied to an HDD for safe keeping.
The image is then simply restored to each of the SSDs on
test. After imaging the drive the partition is then realigned “on the fly” and the
free space is filled and then deleted to force TRIM. A 20 minute settling time
is allowed before the tests are run, then each of the 6 tests is run and the
results gathered. This process is repeated for each of the drives I am testing.
The test scenarios are as follows.
- Graphics content
- Video editing
- Audio import and compression
- Application multitasking
- Windows defender (full system drive scan)
- GRID 2 gaming test.
Let’s begin the tests.
Myce Reality Suite – Graphics content.
Using ACDSee Pro 3, 100 JPG pictures with an average size of
10MB are imported into the ACDSee library, and then 12 of these JPG files are
then selected for a batch process, of resize, compress the quality to 80%, and
finally write the edited pictures back to the drive. The test is approximately
78% read and 22% write, with an average queue depth of 1.98.
The Toshiba HG6 256GB performs well in this test, and finishes
in fourth place.
Myce Reality Suite – Video editing.
Using Vegas Pro, a 14GB HD MPEG2 video stream is loaded into
the editor, from which 2 segments are then cut and pasted into new segments. There
is a lot of disc caching going on in this test, which is approximately 55% read
and 45% write, with an average queue depth of 1.89.
Once again the Toshiba HG6 SSD finishes in fourth spot
Myce Reality Suite – Audio import and compression.
Using Sony Sound Forge 10, a batch process is run consisting
of importing 30 24bit (192000 Hz sample rate) .wav files, and 100 16bit (44100
Hz sample rate) .wav files which are converted to MP3 audio files with a bit rate
of 128kbps, and the MP3s are then written back to the drive. The test is
approximately 72% read and 28% write, with an average queue depth of 2.62.
This time the Toshiba HG6 takes third place.
Myce Reality Suite – Application multitasking.
For this test I used several popular applications, Microsoft
Word 2007, Microsoft Access 2007, Microsoft Excel 2007, Microsoft Outlook 2007,
Adobe reader, Adobe Photoshop CS3, uTorrent, Windows media player, and Internet
Explorer 9.
This session runs for approximately 12 minutes. The test is
started by downloading a Linux distribution via uTorrent, Windows media player
is then opened, and a 1080p video file is opened and played for the duration of
the test. Microsoft Outlook is opened and any new emails are received, read,
then replied too, a document in Adobe reader is opened and scrolled from start
to finish, 3 Microsoft Word documents with graphics content are opened, browsed
and some sections of the documents are copied and pasted into a forth document
and then saved back to the drive. The same applies to Microsoft Access and
Excel. 100 MP3 files are imported into Windows media library. Six JPG images
are loaded into Adobe Photoshop and some minor editing is done and the files
saved back to the drive.
Finally, Internet Explorer 11 is opened with 10 tabs, and
the contents of the 10 tabs refreshed, and browsed while the other applications
are busy in the background.
I would describe the multitasking pattern as moderate to
heavy.
During this test there is approximately 85% reading and 15%
writing, with an average queue depth of 6.73.
With the higher queue depths in this test, the Toshiba HG6 256GB
SSD is able to show what it can really do when pushed hard, and performs well,
finishing in first spot.
Windows Defender (full system drive scan)
A full system drive scan is selected on drive C: and then
run. The test is approximately 99% reading and 1% writing, with an average
queue depth of 1.2.
The Toshiba HG6 SSD has performed very well in this test,
finishing in fourth place.
GRID 2 gaming test
The game is launched and then a pre-saved level is loaded.
The test runs until the loaded level starts. The test is approximately 98% reading
and 2% writing, with an average queue depth of 1.
Once again, the Toshiba HG6 SSD has performed extremely well
in this test, and takes the top spot.
Summary
I firmly believe that the Myce Reality Suite gives a very
good overall picture of how a drive can perform in the real world and, in this
case, the Toshiba HG6 256GB SSD is clearly a very capable performer.
Now let’s head to the next page, and see how well the
drive performs after heavy use....
Filling up the SSD with data
For obvious reasons, when an SSD is tested, the drive is
always tested as a spare drive, and is generally always empty (no data on the
drive) during the synthetic benchmarks. There is no other way of having a level
playing field for all the SSDs under test. This of course changes during the
real world tests we conduct here at Myce.wiki.
Real users of course don't buy an SSD for it to remain
empty, and how full the SSD will eventually become varies from one user to the
next. What I thought would be useful is to run tests on the SSDs with real data
on the drives, and at different levels regarding how full the drive is.
For these tests the SSD is connected as a spare, and I test
at three different levels.
- Level 1: There an operating system installed on the
SSD, and all the applications that I use are also installed. In my case
that amounts to approximately 44GB of data on the SSD. - Level 2: The SSD is filled to 60% of its formatted
capacity. - Level 3: The SSD is filled to 80% of its formatted
capacity.
For the 60% and 80% tests, the type of data varies from
compressible to incompressible data, and file sizes range from a few Kilobytes
to very large files of several Gigabytes, then a single run of Anvil's SSD
Benchmark is run (100% incompressible).
It is also worth noting that the larger capacity SSDs will
tend to slow down less than their smaller counterparts, as the larger SSDs will
have more free NAND available to work with, and this is only a quick burst test
that all members will be able to run for themselves. The real test is the Myce
Sustained Performance test, which you can find a little further down the page.
In the graph below, I present the results.
Filling up an SSD with data can certainly cause a slowdown to
occur on some SSDs, and in the case of the Toshiba HG6 this was certainly the
case. The 'adaptive SLC emulation' appears to cover up to 50% of the drives
capacity. Although there is little evidence of this occurring in the Anvils
benchmark when the drive is filled to 60% of its capacity, it does clearly show
that write speeds have dropped off substantially when the drive is filled to
80%. Reading speeds are unaffected.
This however is a short burst test and, in the graphic below,
you can clearly see the slowdown that occurred when I copied a large file over
to the HG6 when it had reached the 50% full mark.
To test if this slowdown was really occurring, I copied over
a very large file to the Toshiba HG6. When the file copy was started, the drive
was approximately 45% full. One can clearly see the slowdown, once the drive
passes the 50% full mark.
Myce Sustainable Performance Test
Over the last few months I have been studying countless
analyzer traces of real computing workloads, and also developing a test that
would accurately emulate and measure how performance is sustained over a period
of time. For obvious reasons, it is not possible to test an SSD review sample
over several months before publishing a review. The solution was to condense
this down to a manageable test, that doesn't take too long to run.
I will make it clear right from the outset that this is not
a torture test. Bringing any SSD to its knees is not helpful in the least, as I
for one would not use any SSD that had slowed down to crawl, just to prove a
point. The Myce Sustainable Performance test, I believe is a tough, but
sensible test pattern to use for measuring how an SSD will be behave once it's pushed
hard over a period of time.
The test pattern is "workstation" based, and
closely emulates a typical video or graphics workstation environment. The
results are measured using the same hardware I use for the Myce Reality Suite
tests, however, the test data and measuring system use a different method.
From the 80% full test listed above, I already have an SSD
with a lot of data on it. Adding to the data that is already there, the
"Sustainable Performance" test data is added. This test data is
approximately 20GB is size, so once this is added the SSD is pretty full.
The test is then run for a period of 20 minutes. 60
performance measurements are taken for every minute of the test, and an average
performance figure is generated after each minute. At the end of the test I
have 20 performance measurements which are then used to generate the graph
below.
The faster SSDs will obviously sustain more writes then the
slower SSDs. For the fastest SSD in this test, the test pattern generated 146GB
of writes, and 193GB of data was read from the SSD during the test.
When reading the graph, you should not pay too much
attention to which drive is the fastest, but instead look at the sustainable
performance curve of each SSD, as this is what this test is all about.
For the SSD that I am reviewing, I will also add a second
graph which looks at the result in more detail.
So let's look at the results.
Sustainable Performance test
Detailed results for the review drive
Since the HG6 was already 80% full before adding the
'Sustained performance' test data, we can see that the HG6 workstation
performance is lower than the test results obtained from the IOMeter
Workstation emulation test. When that test was performed, the SSD was empty. To
recap, the IOMeter workstation emulation test results showed that the HG6 was
capable of approximately 444 MB/s. In this sustained performance test, the HG6
returned approximately 328MB/s. But, what is worth noting is, this value is
sustained extremely well throughout the test, with only a marginal drop in
performance very near the end of the test.
This concludes our review. To read the final thoughts and
conclusion, click the link below....
Final thoughts and the conclusion
User experience
A modern operating system such as Windows 8 rarely does one
thing at time; it processes hundreds of threads at once. Just take a look at
the processes and services that are running in task manager for an idea of how
much is going on, even with the PC idling at the desktop. When you start
running applications on top of this, the workload increases in line with the number
and type of applications you are running. It’s also fair to say that many of
these processes are already loaded into system RAM, but many are also loaded into
and unloaded from RAM to the system drive as and when they are required.
If we look at the 4 basic requirements for a really fast
SSD, they are as follows.
- Small file threaded performance needs to be high.
- Small random file performance needs to be high.
- Sequential read and write speeds need to be high.
- Fast access times.
The Toshiba HG6 SSD series SSD has all of these attributes
in abundance, and feels very snappy in use as a system drive.
Stability
I have only had the Toshiba HG6 SSD series SSD for a few
weeks, so it’s not possible to comment on the drive's long term reliability. What
I can say is that during the testing period, the Toshiba HG6 256GB has been
100% stable and has caused no problems whatsoever.
The Toshiba HG6 SSD is as “plug n play” as it gets. There
are no special tweaks needed other than simply making sure that AHCI SATA mode
is enabled in the system UEFI (BIOS), and installing the latest Intel RST SATA
drivers, if you want to get the best performance and compatibility out of this
SSD.
Conclusion:
Let us summarise the most important positive and negative
points below:
Positive:
- Silky smooth operation as a system drive.
- Outstanding mixed read/write performance.
- Excellent sequential reading and writing performance, even
at very low queue depths. - Excellent 4K random writing performance, at low queue
depths. - Excellent 4k random reading performance at very low, and
very high queue depths. - TRIM support under Windows 7 and Windows 8.
- Completely silent operation.
- Fast operating system start-up and shutdown times.
- Very fast in 'real world scenarios'.
- Competitively priced.
- 3 year warranty.
Negative:
- Writing performance drops off dramatically once the drive
is filled beyond 50% of its capacity.
To sum up, this is what I
would say:
As an operating system drive, the Toshiba HG6 256GB SSD is
pretty hard to fault. Although writing performance does drop off once the SSD
is filled to more than 50% of its capacity, this has very little effect on day
to day operation of the SSD. When I discovered that this slowdown was real, I
ran the HG6 as my operating system drive for a couple of days, and could not
detect that this slowdown in writing performance was having any negative impact
on the SSD's performance.
The synthetic benchmark results for the Toshiba HG6 are
good, but hardy inspiring. However, as I have repeated many times before,
synthetic benchmarks mean very little in the real world. In the real world the
Toshiba HG6 256GB SSD is a screamer, and one of the very fastest SSDs I have
ever tested, which the PCMark, and Myce Reality test results prove.
You should keep in mind that the Toshiba HG6 SSD I have
tested in this article is an early sample. So between now and the HG6's
official launch, there is still time for Toshiba to tweak the firmware and get
even more performance from this series of SSDs. As it stands, the Toshiba HG6
series of SSDs should certainly be on your shortlist, if you are intending to
buy an SSD in the near future.
Price and availability
The Toshiba HG6 SSD will be available sometime during Q2 of
2014. The suggested pricing is as follows.
- HG6 120GB - Approximately £78
- HG6 256GB - Approximately £140
- HG6 512GB - Approximately £300
The parting sentence is:
“The Toshiba HG6 256GB is an excellent, high performance,
mainstream SSD, with a performance profile ideally suited to real world computing”.
Rating system
The editor rating is based on the following key factors.
- Performance
- Stability (is the device stable?)
- Price
- Warranty
- Supplied accessories (what is included in the package)
Thanks to:
|
|
EFD Software for |
|
|
Alex |
|
|
|
|
|
FutureMark for |
You may comment on this review below.
